Description
Elevator lop display board XEPDM-23B Brief Introduction
|
Product Name |
Elevator lop display board |
| Model Number | XEPDM-23B |
|
Quality
|
Original.Brand New
|
|
Payment
|
T/T. Paypal. Western Union
|
|
Delivery
|
3-5 Working Days
|
|
Packaging
|
Packed by carton
|
Elevator LOP Display Board XEPDM-23B – 23″ Floor & Arrow Signalling Made Simple | Nanjing Zhuye Elevator Parts
The first thing passengers see while waiting is the landing indicator. The XEPDM-23B 23-inch widescreen LOP display turns that moment into a premium experience: full-HD floor numbers, animated arrows, video adverts and emergency messages are all delivered with 1,000 cd/m² brightness and 178° viewing angles. When pixels fade or the screen stays black, the entire building looks outdated. Nanjing Zhuye Elevator Parts keeps genuine XEPDM-23B boards – complete with power supply, HDMI cable and mounting frame – in stock for next-day despatch worldwide, helping contractors restore a modern, trustworthy appearance without costly OEM delays.
Product snapshot
-
Part number XEPDM-23B, hardware rev. G2, firmware XEP-3.11
-
23.0″ IPS LCD, 1920 × 1080 Full HD, 1,000 cd/m², 3,000 : 1 contrast
-
LED backlight, 50,000 h lifetime, auto-dimming 0-100 % via 0-10 V or PWM
-
24 V DC ±10 % input, 45 W typical, 60 W max, reverse-polarity protected
-
2 × HDMI 1.4, 1 × VGA, 1 × USB for media update, 1 × RJ-45 for remote control
-
ARM Cortex-A53 quad-core, 1 GB DDR4, 8 GB eMMC, hardware H.264 decoder
-
On-board 8 Ω, 3 W amplifier + 3.5 mm line-out for voice announcements
-
Operating temperature −10 °C to +60 °C, humidity 5-95 % RH non-condensing
-
IP31 aluminium frame, 535 × 325 × 35 mm, 3.8 kg, VESA 200 × 200 mm
-
CE, FCC, RoHS, REACH certified, flame class UL 94-V0
Where it works
-
Landing Operating Panels (LOP) in ThyssenKrupp EVOLUTION, ES-P, ES-G, TWIN systems
-
Car Operating Panels (COP) when used with video intercom or advertising overlay
-
Modernisation packages replacing 7-segment, dot-matrix or smaller TFT indicators
-
Any controller outputting HDMI or VGA floor signal, 0-10 V brightness control
Installation method – 15-minute plug-and-play
-
Place lift on inspection mode; switch OFF local breaker.
-
Remove old indicator: release four M4 screws; withdraw unit.
-
Photograph wiring; note 24 V polarity and video cable type.
-
Mount supplied frame to wall or LOP cut-out; drill 4 × Ø5 mm holes if needed.
-
Connect 24 V DC (red +, black −) to X1; torque 0.5 Nm.
-
Plug HDMI or VGA cable into X2/X3; tighten locking screws.
-
If audio used, connect 3.5 mm jack to X4.
-
Insert display into frame; latch spring clips.
-
Power up; screen shows “XEPDM-23B” logo for 2 s, then auto-switches to floor signal.
-
Adjust brightness: OSD menu → Brightness 70 % for typical lobby lux of 200 lx.
-
Cycle car to top and bottom floors; confirm arrow direction and colour change.
-
Seal cable entries with supplied grommets; update maintenance log.
Replacement cycle & maintenance
Although solid-state, large displays age by backlight hours and thermal cycles. EN 81-70 and site audits suggest:
-
Visual inspection every 6 months: clean ventilation slots, check for swollen capacitors.
-
Backlight hours: replace when on-screen timer > 45,000 h (≈ 9 years at 14 h/day).
-
Immediate replacement if:
– backlight flickers or dark zones appear,
– HDMI shows “No Signal” although controller outputs correctly,
– temperature > 70 °C on heat-spreader (fan failure),
– USB update fails (eMMC corruption).
Pro tip: 70 % of premature failures are traced to loose HDMI connectors—re-seat and apply thread-locker every year.
Maintenance tips from Nanjing Zhuye Elevator Parts
-
Always use shielded HDMI cable < 2 m to avoid digital sparkles.
-
Never hot-plug 24 V during lift run—spikes can kill the DC-DC converter.
-
Keep a spare XEPDM-23B in every service room; at 3.8 kg it fits on a shelf and saves a callback.
-
After lightning storm, check 24 V ripple < 1 V; high ripple overheats the LED driver.
-
Order the “LOP Display Kit” (board + 2 m HDMI cable + 24 V harness) from Nanjing Zhuye Elevator Parts to eliminate on-site splicing.
Why buy from Nanjing Zhuye Elevator Parts?
We import XEPDM-23B directly from the OEM assembler, age-test every screen for 4 h at 60 °C, and ship with a 24-month replacement warranty. Stock is stored in foam-lined cartons to prevent pressure damage. Orders placed before 15:00 China time leave the same evening via DHL Express, arriving Europe or North America in 2–4 days. Bulk pricing starts at three pieces; we can pre-load your logo splash-screen and include a loaner unit to keep lobbies bright during the swap.
Conclusion
The XEPDM-23B LOP display is the face your passengers judge every day. By installing the genuine unit, setting brightness to spec and replacing it before the backlight fades, you turn every wait into a silent advertisement for quality and safety. Stock genuine XEPDM-23B from Nanjing Zhuye Elevator Parts today—because when the screen goes black, the whole building looks outdated.
