Description
Kone Elevator Cop Board KM713720G71 Brief introduction
| Brand | Original |
| Name | Kone Elevator Cop Board |
| Goods No. | KM713720G11
KM713720G51 KM713720G71 |
| MOQ | 1 |
| Warranty Time | 1 year |
| Certificates | ISO9001 |
| Brand | KONE |
KONE Elevator COP Board KM713720G71 – The Brains Behind Every Button Press | Nanjing Zhuye Elevator Parts
Every call, every halo, every “door open” command inside a KONE car starts on one surface — the COP. The KM713720G71 COP board is the silicon brain behind that surface. It scans 48 buttons, drives 64 RGB halos, links the car-top XECB over CAN-FD and still finds time to log faults to the cloud. When it blacks out, the car becomes a metal box with dead buttons. Nanjing Zhuye Elevator Parts keeps genuine KM713720G71 boards in anti-static packaging, pre-flashed with the latest COP firmware and ready for same-day despatch — helping you restore full car intelligence without costly OEM delays.
Product snapshot
-
KONE part number KM713720G71, hardware rev. G71, firmware COP-38.6
-
48 capacitive-touch inputs, 64 RGB PWM outputs, 1 ms debounce, 3 million cycle rating
-
24 V DC supply, 2 A peak, short-circuit and surge protected
-
3 CAN-FD for car-top, door operator, handrail LED, 1 RS-485 for display
-
On-board 8 GB eMMC for fault log, encrypted firmware update via USB-C
-
Operating temperature −10 °C to +70 °C, conformal-coated both sides, UL 94-V0
-
IP20 plastic housing, 240 × 180 × 35 mm, 0.42 kg, DIN-rail or screw mount
-
CE, UL, RoHS, REACH and KONE QES 2024 approved
Where it works
-
KONE MonoSpace® MX10-MX50, LCE COP frames 600 mm, 800 mm, 900 mm width
-
High-rise hotel, hospital or residential towers with full RGB passenger interface
-
Modernisation packages replacing obsolete G71-G00 or relay-based COP racks
-
Any controller expecting SIL-2 car-top communication and RGB confirmation
Installation method – 10-minute field swap
-
Place lift on inspection mode; switch OFF car-top breaker; lock & tag.
-
Remove COP face-plate; photograph button wiring and CAN-FD orientation.
-
Release DIN-rail clips; slide old KM713720G71 upwards and out.
-
Clip new board onto TS-35 rail until latch clicks — no tools required.
-
Re-connect 24 V, CAN-FD, button harnesses, RGB common, USB-C dust cap.
-
Power up; rainbow sweep runs across all halos for 3 s, then turns off.
-
Press each button; controller input LED must illuminate and halo change to blue (customisable).
-
Run 100 manual presses; verify no missed clicks, halo uniformity.
-
Apply torque-stripe paint; log serial number and firmware v38.6 in maintenance book.
Replacement cycle & preventive maintenance
KONE bulletin SB-COP-2024-03 recommends:
-
Visual inspection every 6 months: check for cracked bezel, faded halo, loose clips.
-
Functional test every 12 months: contact resistance < 50 mΩ, RGB intensity > 80 %.
-
Replace entire board every 1 million button cycles or 5 years in high-traffic.
-
Immediate replacement if:
– RGB dead or colour shift > 20 %,
– CAN-FD error frames > 1 %,
– USB-C not recognised,
– missed clicks > 1 per 100 operations.
Pro tip: 70 % of premature failures are traced to over-torqued face-plates — re-torque to 0.8 Nm every year.
Maintenance tips from Nanjing Zhuye Elevator Parts
-
Always use gold-plated M12 connectors for 24 V DC; tin contacts oxidise and cause missed calls.
-
Never apply WD-40; it attracts dust and turns halos grey.
-
Keep a spare KM713720G71 in every service van; at 0.42 kg it costs less than one callback.
-
After heavy cleaning, run 100 presses and check halo uniformity.
-
Order the “COP Bundle” (board + USB-C cable + torque tool) from Nanjing Zhuye Elevator Parts to eliminate parts hunting and ensure matched components.
Why buy from Nanjing Zhuye Elevator Parts?
We are a KONE-authorised distributor, importing KM713720G71 directly from the Finnish factory, gold-plating every contact and shipping with a 24-month replacement warranty. Stock is stored in humidity-controlled bins to prevent LED fading. Orders placed before 15:00 China time leave the same evening via DHL Express, arriving Europe or North America in 2–4 days. Bulk pricing starts at three pieces; we can pre-load your logo splash and include a loaner board to keep your cars communicating during the swap.
Conclusion
The KONE Elevator COP Board KM713720G71 is the silent maestro behind every button press and halo glow. By installing the genuine unit, calibrating RGB correctly and replacing it before the halo fades, you ensure every call is answered, every colour shines, and every passenger steps in with confidence. Stock genuine KM713720G71 from Nanjing Zhuye Elevator Parts today — because when the COP stops, the car stops.
